Drying times doubled within a week of cleaning behind the dryer. Nothing was wrong before. Nothing obvious is wrong now.
This is the most common dryer vent fault we find, and it is caused by the dryer being moved.
What actually happens
The exhaust hose runs from the back of the dryer to a fitting in the wall. In most laundry rooms there is very little space between the two — often only a few inches.
When the dryer is pulled forward, the hose comes with it and loses its shape. When the dryer is pushed back, the hose has nowhere to go. It folds, kinks, or flattens between the machine and the wall, and the dryer holds it there.
From the front everything looks finished. The dryer is flush against the wall, the room is clean, the job is done. Behind it, the exhaust passage has been reduced to a fraction of its diameter.
The effect is immediate. Airflow drops the moment the hose folds, so drying times change on the very next load. That abruptness is the signature — and it is the main thing that separates this from lint buildup, which takes seasons to show up.
Why the symptoms fool people
Because the problem appears right after cleaning, the two get connected in the wrong order. People assume the cleaning disturbed something inside the duct, or that the dryer itself is failing.
Both are reasonable guesses. Neither is what happened. The duct is fine and the dryer is fine; the hose between them is folded shut.
The same thing happens after an appliance delivery, after flooring work, after a washer is replaced, and after anything else that involves sliding the machine out and back.
Which hose types fail this way
The material matters a great deal.
Flexible foil and plastic hose is the worst offender. It crushes under almost no pressure and does not spring back. Once it has been folded flat for a few weeks it tends to stay that way even if you straighten it. It also tears along the fold line.
Semi-rigid metal holds its shape better and resists crushing, though it can still be kinked if forced.
Rigid metal duct does not crush. Where the layout allows it, this is the better long-term answer — it is also smoother inside, so less lint settles along it in the first place.
Plenty of homes around Silver Spring and DC still have foil hose from an installation decades old. It worked when it was put in; it has simply been moved a few too many times since.
How to check
Pull the dryer out far enough to see behind it, and look rather than touch.
You are looking for the hose folded sharply where it meets the wall, flattened against the wall, pulled loose at either end, or split along a crease. Lint on the floor behind the dryer is another sign — it suggests exhaust escaping before it reaches the wall.
If the hose looks sound, the restriction is further along the run and you cannot see it from the laundry room.
How to avoid it
A few things make a real difference:
Leave the hose as much room as the space allows. A hose that is slightly too long and gently curved survives being moved. One cut exactly to length has no slack and folds the first time.
Watch the hose while pushing the dryer back, not the front of the machine. Push a few inches, check, push again. Most of the damage happens in the final few inches.
Do not push the dryer fully flush if that means crushing the hose. A small gap at the front is better than a closed exhaust.
Consider rigid duct with a short flexible connector if the dryer gets moved often. The rigid section cannot be crushed and the short connector gives the movement it needs.
What it costs you if it stays that way
A restricted vent is not only slower. Every cycle runs longer, which uses more energy and puts more hours on the machine. Heat and moisture that should be leaving the house stay in the laundry room.
There is a knock-on effect worth knowing about. Restricted airflow makes lint settle along the duct rather than being carried out, so a vent that has been partly crushed for a year is usually also packed with lint. That is why these jobs frequently turn out to need both a repair and a cleaning, as we cover in dryer vent repair or cleaning. If the vent is damaged, see our dryer vent repair service.
And the longer-term matter: the U.S. Fire Administration identifies failure to clean as the leading contributing factor in home dryer fires. A crushed hose accelerates exactly the accumulation that creates that risk.
Frequently asked questions
My drying times changed right after I cleaned behind the dryer. Is that a coincidence?
Almost certainly not. A sudden change immediately after the dryer was moved points to the hose being folded or crushed when the machine went back. It is the most common cause we see.
Can I just straighten the hose myself?
You can try, and with a minor kink in otherwise sound hose it sometimes works. Foil or plastic hose that has been folded flat for a while usually does not recover its shape, and hose that has torn along the fold needs replacing rather than straightening.
How much space does a dryer need behind it?
Enough for the hose to curve rather than fold. The exact figure depends on the hose type and the fitting position, and the manufacturer’s installation instructions for your dryer are the authority on clearances. The practical test is whether the hose stays open when the dryer is in place.
Is a crushed hose a fire risk?
It contributes to the conditions behind dryer fires: restricted airflow, higher temperatures and faster lint accumulation. It should be dealt with rather than lived with.
Should I replace foil hose with rigid duct?
Where the layout allows, rigid or semi-rigid metal is the better choice — it resists crushing and holds less lint. Whether it suits your installation depends on the route and the clearance behind the machine, which is something to look at rather than decide in advance.
Worth a look?
If drying times changed suddenly and the dryer has been moved recently, there is a good chance the answer is behind the machine.
Call More Fresh Air Services at 888-509-3828 or request an estimate. Mention that the dryer was moved and roughly when the change started. We are insured and fully registered.
See dryer vent cleaning in Silver Spring MD for what the work covers.
Source: U.S. Fire Administration, Clothes Dryer Fires in Residential Buildings.